Slip the remaining compression nut and ferrule over the refrigerator end of the new water line. She attended Tarrant County College and studied English composition. The valve connected to the right side of the faucet is the cold water supply line. She writes mainly home improvement, health and travel articles for various online publications. How would you like to contact us?
Connect and install the water line to your refrigerator
Do not over-tighten it, as over-tightening will cause a leak. In the image, dating C demonstrates how it will look when installed. Thank you for visiting Samsung U.
Find your water supply lines beneath your sink. This image is also available in your user's manual. Plug your refrigerator into the wall.
Usually, this will be at some other existing water hookup point, like the water supply lines connected to your sink faucet or dishwasher. The kit provides you with the required parts to hook up a water line to your refrigerator. If you don't have a convenient water supply pipe and valve near the refrigerator, you must instead find another spot to hook up the water line. If your home doesn't have a water line installed from a previous refrigerator, you will need a water line that can run between the water pipes in your home and your fridge. The tee adapter connects to the water supply shutoff valve.
Turn the water on and check for leaks. Insert the new water line into the opening on the tee. Coil the excess water line behind the refrigerator. Visit the download center to get a copy.
How to Hook Up a Water Line to a Refrigerator
How to Install a Water Line for a Refrigerator
Tighten the connections slightly if you see a leak. Social Support Contact us on Twitter or Facebook and we'll reply with an answer to your question or issue. Connect and install the water line to your refrigerator.
- Connect the water supply line to the refrigerator.
- First, locate the shutoff valve under the kitchen sink where you want to connect the new water line.
- If you find water drops or a leak in the connection areas, turn off the main water supply.
- Turn the water supply valve on and check for leaks.
- Then you'd need to twist the valve until it pierces your water line.
Install a new refrigerator water supply line
She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction. Consult user manual for more complete information. Thread the water line, included in the ice maker installation kit, from the area behind the refrigerator to beneath the sink.
- Question about a promotion?
- The water lines are typically sold in kits and are not included with the refrigerator.
- Disconnect the faucet supply tube from the shutoff valve.
- All information included herein is subject to change without notice.
- You can use the water line leftover from your previous refrigerator, or start fresh with a new kit from the hardware store.
Thank you for your feedback! Wrap the female thread on the opposite end of the adapter with thread-seal tape. Also, check for leaks where the supply tube connects to the refrigerator before pushing the appliance back into place. Push the refrigerator against the wall. Slip the compression nut that came with the kit over the newly installed supply line.
Turn the supply line on once again. Connect the Supply Tube to the Refrigerator. Again, the kit's instructions will tell you how to do this.
Turn the cold water on the supply line clockwise to close it. Thread the ferrule from the kit onto the new line. As mentioned above, the water supply line is not included with the refrigerator and is typically sold as a kit at your local hardware store if you don't have one already installed in your home. In most cases, the water line can be run from a kitchen faucet water supply line through the kitchen cabinets and over to the refrigerator.
This Old House
Use pliers to untwist the faucet supply line from the cold water supply valve. Connect the line to the water line connector on the back of the refrigerator. If there are no fixure shutoff valves, you can turn off the water by closing the main water supply valve to the entire house.
Or continue shopping on Samsung. Turn the cold water supply valve on beneath the sink. Flex water supply tubes are available in either a tough plastic nylon mesh or braided steel. Tighten the connection just slightly more than hand-tight, using pliers.
Shut off the water at the valve that controls the cold-water supply pipe to the faucet. Attach the Adapt-a-Tee adapter to the shutoff valve, tightening by hand at first. Ask the Community Browse answers, ask questions and get solutions from other Samsung customers. Adapt-a-Tees can be used in many situations where you need an extra line.
If running the line through the cabinets is not feasible, you might need to run a line through the floor and up to where the refrigerator is located. After installation, check the water pressure by dispensing water. Drill as close to the back wall of the cabinet as possible, so you do not lose storage space inside the cabinet. Leave the excess water line behind the refrigerator.
Twist the male end of a quick-tee adapter onto the valve. They come in various sizes to suit whatever situation you have. Keep in mind that you will need a compression nut at both ends, vn dating online and some kits only come with one.
Connect and install the water line to your refrigerator
If so, your job is very easy. An Adapt-a-Tee is an ideal plumbing fitting for this purpose. Check the connections, dating argentina and tighten when necessary. Watch for leaks at all the connections.